CHANGZHOU HUAYUAN DAYING EQUIPMENT CO.,LTD
Tel:0519-88679278 88679111
Serive:0519-88672111
Email:czhugc@163.com
Add:Sanhekou Industrial Development Zone, Zhenglu Town, Changzhou City
Website:www.chinahuayuan.com

CHG series flow through type oven
CHG series flow through type oven

 

● CHG Series Laminar Flow Type Over

CHG系列穿流式烘箱

Working principle :
In the traditional horizontal flow tray dryer, air flow only in the surface material, the disadvantage is the low heat transfer coefficient, heat utilization rate, drying time is long. And because of the defect of structure, can not fully comply with the "GMP" drug production specification. In order to overcome the above shortcomings. I plant according to foreign advanced technology design and development of the flow type dryer, its working principle :
This machine by the wind turbine will be a part of the fresh air through the beginning, middle and high efficiency filter. To achieve one hundred thousand purification, through the steam heat exchanger, so that the air is heated to a certain temperature. It makes the hot air purified by the left shunt layer plate to make hot air, the average through each layer of dried material. Wet air from the air duct under the pan tilt out, part of the wet air discharged outside the oven by the centrifugal fan. Another part of the air to continue circulating heating. Achieve the purpose of drying.

Characteristic :
Each circulation of the hot air is filtered through the sub high efficiency or high efficiency filter, which can effectively avoid the deterioration of the entrained material in the air during the cycle and the heating process, and the pollution of the medicine. Fully comply with the "GMP" drug production specifications.
Through flow type oven than advection type oven drying capacity, each layer thickness of raw materials for horizontal flow type oven is more than three times.
The drying area of the flow type drying oven is large and the efficiency is high, and the capacity is 3-6 times larger than that of the flat flow type drying oven, and the cost is lower.
Suitable for all kinds of granular, block items dry.
Easy to operate, easy to clean and change, and the fault is low.
Air inlet and outlet air filter, will not be contaminated by dry materials, affecting its quality. Oven heating heat source can be steam or electric heating.

Schematic diagram of CHG-C- type I oven

CHG系列穿流式烘箱

Schematic diagram of CHG-C- type

CHG系列穿流式烘箱

technical parameter :
Model specif
ication
Each drying capacity
(kg)
Equipped with the power of
(kw)
Steam consu
mption
Heating area
(m2
Air volume
(m3/h)
Upper and lower tempe
rature diffe
rence
Coal plate size The number of Pan weight Outline dime
nsion
CHG-C-Ⅰ 100 7 40-80 50 4000-7300 4000-7300 550×610×80 10 2200 2580×1400×2280
CHG-C-Ⅱ 200 7.5 80-120 80 7200-15800 7200-15800 550×610×80 20 4000 3500×1600×2280

Summary :
Hot air circulation oven drying room is the traditional alternative products, after several upgrades, the thermal efficiency of oven drying room from the traditional 3-7% has been raised to 45%, up to 50%, reaching the advanced level at home and abroad. And in 1990 by the State Drug Administration issued the industry standard, unified model for RXH, it is a supplement to the use of steam, then discharged from the exhaust port, continue to add fresh air and continuously discharging hot air, so to keep the relative humidity inside the oven proper. The biggest characteristic of this oven is that most of the hot air is circulated in the oven, which can increase heat transfer and save energy. It is the use of forced ventilation to reduce the upper and lower temperature. I plant the factory oven, are equipped with air distribution device, the user can be used before the wind to adjust, so that the temperature difference between the top and bottom is in the best state.
CT series of oven without automatic control, using 4-72 centrifugal fan, CT-C series oven adopts axial flow fan with automatic constant temperature system, and a computer control system.
Hot air circulation oven drying equipment are common, wide applicability, disc type drying equipment, used in pharmaceutical, chemical, food, light industry, heavy industry, raw materials, products in addition to heating and temperature. Such as: raw materials, raw materials, Chinese herbal medicine, powder, pill packaging, size pigments, dyes, dehydrated vegetables, food, plastic, resin, paint, and other electrical components.

Model description and features :
Heating heat source: steam, electricity, far infrared, steam and electricity dual-use, for the user to choose.
Use temperature: steam heating 50-140
Electricity, far infrared temperature 50-350
Common steam pressure 0.02-0.8MPa(0.2-8kg/cm2)。
Equipped with electric heating type I according to 15kw calculation, 5-8kw/h and so on.
Special requirements can be non-standard design.
Use temperature is greater than 140 or less than 60 degrees Celsius, to be in order to indicate.
The factory car baking pan, size uniform, interchangeable.
Pan size:460x640x45。

technical parameter
Industry standard model
Model specification
Each drying capacity
(kg)
Equipped with the power of
(kw)
Steam consumption
(kg/h)
Radiating area
(m2)
Air volume
(m3/h)
Up and down temperature difference
()
Baking disk (only)
Outline dimension
width x deep x height
(mm)
Matching baking
()
RXH-14-B CT-I 100 1.1 20 20 1400 ±2 48 2430x1200x2375 2
RXH-27-B CT-II 200 1.1 40 40 5200 ±2 96 2430x2200x2433 4
RXH-41-B CT-III 300 2.2 60 80 9800 ±2 144 3430x2200x2620 6
RXH-54-B CT-IV 400 2.2 80 100 9800 ±2 192 4380x2200x2620 8
RXH-5-C CT-C-O 25 0.45 5 5 3450 0 16 1550x1000x2044 0
RXH-14-C CT-C-I 100 0.45 18 20 3450 ±2 48 2300x1200x2300 2
RXH-27-C CT-C-II 200 0.9 36 40 6900 ±2 96 2300x2200x2300 4
RXH-41-C CT-C-III 300 1.35 54 80 10350 ±2 144 2300x3220x2000 6
RXH-54-C CT-C-N 400 1.8 72 100 13800 ±2 192 4460x2200x2290 8
RXH-18-C CT-C-IB 120 0.9 20 25 6900 ±1 48 1460x2160x2250 2
RXH-41-B CT-C-IS Special baking bottle 2.2 60 100 6900 ±2   1140x6160x3240 6
RXH-25-A   High efficiency and high temperature far infrared sterilizing oven 1200x1000x1600 1